My RJ45 standard a cable broke. I tried fixing it in but i cant align the clolored wires properly , because they all turn and twist when i try to put them into the clear plastic thing.
You cant re-use an old connector, you’ll have to crimp on a new one. It may or may not be worth buying the tool/ends depending on the length of the cable.
You can buy a cable crimper and a bag of the ends on Amazon, prob for $20-$40, but if it’s just one small patch cable you’re trying to fix, you can probably buy that for $5.
I ran Ethernet through my whole house and outside for cameras, so it was worth it to me to buy the tools and spools of cable.
If it’s a premade patch cable…good fuckin luck. It’s possible but they’re usually too thin and flexible to recrimp without a bunch of attempts. Bulk wire is a lot stiffer and maintains its shape.
Are you using pass through (EZ) connectors? That makes it a ton easier.
Make sure you’re straighting them out before hand with the tip of a screwdriver makes it easier. Also look for rj45 connectors with a load bar, makes it a lot easier since you can feed them one at a time and make sure they are aligned properly, often they also come with pass through connectors and you should be able to do that in no time.
My trick is to wiggle them back and forth a few times between your thumb and index finger while pulling on them just a bit. This warms them a bit from your hand and the bending. And the push through connectors are a godsend since you can strip them a little long.
Make your stranded end nice and long and easy to “comb” and flatten out. Get all your pairs lined up and in order and flatten the wires together on a table or other work surface.
I usually cut about 3 or so inches of sleeve off the cable to expose the strands. But same thing applies if you can only cut an inch off, just a little more difficult.
Assuming you have passthrough rj45 ends or whatever they’re called, you can just slip on your end and crimp and let the tool trim the excess wire.
If you don’t you get to go through the process of trimming down and getting the tiny stubs to stay together enough to slide into the connector.
There are also connectors that let the cable through the holes in the end, completely removing the need to try and get the strip length exactly right. It’s worth looking into if you have to do this more than a once or twice. As a quick example; https://www.amazon.com/Klein-Tools-80024-Racheting-Installation/dp/B09FWH5RFF/
You are not logged in. However you can subscribe from another Fediverse account, for example Lemmy or Mastodon. To do this, paste the following into the search field of your instance: !selfhosted@lemmy.world
A place to share alternatives to popular online services that can be self-hosted without giving up privacy or locking you into a service you don’t control.
Rules:
Be civil: we’re here to support and learn from one another. Insults won’t be tolerated. Flame wars are frowned upon.
No spam posting.
Posts have to be centered around self-hosting. There are other communities for discussing hardware or home computing. If it’s not obvious why your post topic revolves around selfhosting, please include details to make it clear.
Don’t duplicate the full text of your blog or github here. Just post the link for folks to click.
Submission headline should match the article title (don’t cherry-pick information from the title to fit your agenda).
Weeping helps.
I have managed to fix it, thanks for the tips!
I have managed to fix it, thanks for the tips!
You cant re-use an old connector, you’ll have to crimp on a new one. It may or may not be worth buying the tool/ends depending on the length of the cable.
You can buy a cable crimper and a bag of the ends on Amazon, prob for $20-$40, but if it’s just one small patch cable you’re trying to fix, you can probably buy that for $5.
I ran Ethernet through my whole house and outside for cameras, so it was worth it to me to buy the tools and spools of cable.
I have the tools and a fresh connector but my problem is that i cant align the wires proprerly, they end up in the wrong slots.
If it’s a premade patch cable…good fuckin luck. It’s possible but they’re usually too thin and flexible to recrimp without a bunch of attempts. Bulk wire is a lot stiffer and maintains its shape.
Are you using pass through (EZ) connectors? That makes it a ton easier.
Make sure you’re straighting them out before hand with the tip of a screwdriver makes it easier. Also look for rj45 connectors with a load bar, makes it a lot easier since you can feed them one at a time and make sure they are aligned properly, often they also come with pass through connectors and you should be able to do that in no time.
It’s a skill you develop with time… I guess, cause I haven’t developed it yet.
Things that usually help me with this: Straighten the wires while putting them in order
If cables are too stiff, you can always either cut their tips or use a plier
Pressing with a finger can help you hold the wires in order
While ordering them, you can try the wires on the rj45. It has little guides that help you straighten the wires.
My trick is to wiggle them back and forth a few times between your thumb and index finger while pulling on them just a bit. This warms them a bit from your hand and the bending. And the push through connectors are a godsend since you can strip them a little long.
Make your stranded end nice and long and easy to “comb” and flatten out. Get all your pairs lined up and in order and flatten the wires together on a table or other work surface.
I usually cut about 3 or so inches of sleeve off the cable to expose the strands. But same thing applies if you can only cut an inch off, just a little more difficult.
Assuming you have passthrough rj45 ends or whatever they’re called, you can just slip on your end and crimp and let the tool trim the excess wire.
If you don’t you get to go through the process of trimming down and getting the tiny stubs to stay together enough to slide into the connector.
Example from eBay listing
Solder it mate.
There are also connectors that let the cable through the holes in the end, completely removing the need to try and get the strip length exactly right. It’s worth looking into if you have to do this more than a once or twice. As a quick example; https://www.amazon.com/Klein-Tools-80024-Racheting-Installation/dp/B09FWH5RFF/